اهلا وسهلا بيييك يا عزيزى الزائر
تتمنى اسرة المنتدى ان يكون المنتدى قد نال اعجابكم
اذا اردت ان تنضم لاسرتنا اضغط التسجيل



 
الرئيسيةاليوميةس .و .جبحـثالأعضاءالمجموعاتالتسجيلدخول

شاطر | 
 

 vernier caliper

اذهب الى الأسفل 
كاتب الموضوعرسالة
bent elbalady
Admin
Admin
avatar

انثى عدد الرسائل : 131
تاريخ التسجيل : 02/09/2008

مُساهمةموضوع: vernier caliper   الخميس سبتمبر 18, 2008 10:33 pm


Reading a Vernier
A Vernier allows a precise reading of some value. In the figure to the right, the Vernier moves up and down to measure a position on the Scale. This could be part of a barometer which reads atmospheric pressure.
The "pointer" is the line on the vernier labelled "0". Thus the measured position is almost exactly 756 in whatever units the scale is calibrated in.
If you look closely you will see that the distance between the divisions on the vernier are not the same as the divisions on the scale. The 0 line on the vernier lines up at 756 on the scale, but the 10 line on the vernier lines up at 765 on the scale. Thus the distance between the divisions on the vernier are 90% of the distance between the divisions on the scale.
http://i33.servimg.com/u/f33/12/93/48/13/vernie10.png
If we do another reading with the vernier at a different position, the pointer, the line marked 0, may not line up exactly with one of the lines on the scale. Here the "pointer" lines up at approximately 756.5 on the scale.
If you look you will see that only one line on the vernier lines up exactly with one of the lines on the scale, the 5 line. This means that our first guess was correct: the reading is 756.5.

http://i33.servimg.com/u/f33/12/93/48/13/vernie11.png
Here is a final example, with the vernier at yet another position. The pointer points to a value that is obviously greater than 756.5 and also less than 757.0. Looking for divisions on the vernier that match a division on the scale, the 7 line matches fairly closely. So the reading is about 756.7.
In fact, the 7 line on the vernier appears to be a little bit above the corresponding line on the scale. The 8 line on the vernier is clearly somewhat below the corresponding line of the scale. So with sharp eyes one might report this reading as 756.73 ± 0.02.
This "reading error" of ± 0.02 is probably the correct error of precision to specify for all measurements done with this apparatus.
http://i33.servimg.com/u/f33/12/93/48/13/vernie12.png
Now we shall use a simulation of a Vernier Caliper. A caliper measures a length, and in the following figure we show a caliper being used to measure the length of an Object. The Object will be placed between the "jaws" of the caliper. The Object is almost exactly 75 mm (2.95 in) long.

In the above photograph, you can see that on the top of the caliper are two "prongs" which can be used to measure an interior dimension. There is also a piece of metal sticking out from the right side of the caliper, which is a depth gauge.
Calipers commonly use a vernier scale. In the simulation below, you may "grab" the jaw of the caliper with the left button of the mouse and move it to some position. When you click on the Show button the distance between the jaws will be shown.

_________________

من وفقد الله فماذا وجد ...ومن وجد الله فماذا فقد
الرجوع الى أعلى الصفحة اذهب الى الأسفل
معاينة صفحة البيانات الشخصي للعضو http://shamsbokra.yoo7.com
bent elbalady
Admin
Admin
avatar

انثى عدد الرسائل : 131
تاريخ التسجيل : 02/09/2008

مُساهمةموضوع: vernier caliper   الخميس سبتمبر 18, 2008 10:45 pm


_________________

من وفقد الله فماذا وجد ...ومن وجد الله فماذا فقد
الرجوع الى أعلى الصفحة اذهب الى الأسفل
معاينة صفحة البيانات الشخصي للعضو http://shamsbokra.yoo7.com
 
vernier caliper
الرجوع الى أعلى الصفحة 
صفحة 1 من اصل 1

صلاحيات هذا المنتدى:لاتستطيع الرد على المواضيع في هذا المنتدى
 :: For production Engineer :: Metrology Science-
انتقل الى: